westonuk002063.jpg westonuk002062.jpg westonuk002061.jpg westonuk002060.jpg westonuk002059.jpg westonuk002058.jpg westonuk002057.jpg
QUICK GUIDE
FUEL
RCV ENGINES
E.D ENGINES
WEBRA ENGINES
A.P ENGINES
MAGNUM ENGINES
WEST ENGINES
TUNED WEST 4 STROKES
FIRE EATERS
FUEL REGULATORS
E.D ENGINES
GLOW PLUGS

ENGINE ACCESSORIES

WEST RECEIVERS
WEBRA ELECTRONICS
WEST ELECTRONICS
JACKPOWER LIPOS
BATTERY PACKS
CHARGERS
RUNTRONIC IGNITION
ARTF AEROPLANES
COMPASS HELICOPTERS
HELI BLADES
GENERAL ACCESSORIES 
CARBON ACCESSORIES
PROPELLERS
GLUE
GENESIS EXHAUSTS
Terms & conditions
westonuk2002026.jpg
WHAT WE NEED TO KNOW TO CREATE A TAILOR
 MADE PIPE
FOR US TO CREATE A TAILOR MADE PIPE FOR YOUR AIRFRAME AND ENGINE WE REQUIRE SOME INFOMATION TO ENABLE US TO CORRECTLY MANUFACTURE THE BEST PIPE FOR YOU AND TO ENSURE THAT IT FITS.
THIS IS A GUIDE TO FIT ONE OF OUR GENESIS MINI PIPES
WE NEED TO NO THE ORIENTATION OF THE ENGINE.
(LOOKING FROM THE FRONT OF THE AIRFRAME)
IN THIS EXAMPLE THE HEAD IS AT 270`
0`
90`
180`
270`
WE NEED TO THE DISTANCE FROM THE FACE PLATE OF THE EXHAUST OUTLET OF THE ENGINE TO THE OUTERMOST PART OF THE AIRFRAME. (THIS INCLUDES ANY UNDERCARRIAGE OR WING THAT COULD BE IN THE WAY)
FUSELAGE
U/C
WING
FUSELAGE
CLEARANCE
U/C CLEARANCE
WING CLEARANCE
I.E THIS PICTURE IS FOR WHEN THE PIPE IS TO RUN DOWN THE UNDERSIDE OF THE FUSELAGE.
I.E THIS PICTURE IS FOR WHEN THE PIPE IS TO RUN DOWN THE SIDE OF THE FUSELAGE.
PIPE
PIPE
WING
WING
FUSELAGE
CLEARANCE
FUSELAGE
CLEARANCE
1.
2.
WE NEED TO KNOW IF THERE IS ANY RESTRICTION GOING REARWARDS (THIS MEASUREMENT IS DONE FROM THE CENTRE OF THE MOTOR EXHAUST OUTLET) DEPENDING ON THE ENGINE ORIENTATION THIS COULD BE THE WING OR UNDERCARRIAGE.
3.
REARWARD
CLEARANCE
FUSELAGE
FUSELAGE
U/C
U/C
WING
REARWARD
CLEARANCE
WE NEED TO KNOW IF THERE IS ANY SIDE THRUST ON THE FIRE WALL AS THIS WILL ALTER THE WAY THE PIPE LAYS
4.
FUSELAGE
TOP
WE NEED TO KNOW WHAT ENGINE YOU HAVE AND THE HOLE CENTRE MEASUREMENTS ON THE EXHAUST PLATE
5.
WE NEED TO KNOW IF ITS FOR FAST FLIGHT OR FOR OR 3D
6.
FAST FLIGHT
3D FLIGHT
WE NEED TO KNOW IF YOUR ENGINE IS ON ITS SIDE AND YOU WANT THE PIPE TO RUN DOWN THE CENTRE OF THE BOTTOM OF THE FUSELAGE THE MEASUREMENT FROM THE CENTRE OF THE EXHAUST PLATE TO THE CRANKSHAFT CENTRE LINE
7.
WE NEED TO KNOW THE DISTANCE FROM THE CENTRE OF THE EXHAUST PORT TO THE FIRE WALL IF WE ARE BUILDING YOU A SWAN NECK MANIFOLD
8.
FUSELAGE

?
?
?
?
?
?
?
?
?
?
WE ONLY WORK FROM YOUR MEASURMENTS SO MAKE SURE YOU GET IT RIGHT.
A GUIDE TO HOW LONG OUR PIPES ARE IS VERY HARD AS IT WILL CHANGE DEPENDING ON THE STAND OF DISTANCE. THE LONGER STAND OFF THE LESS IT WILL PROJECT BACK. MEASUREMENT IS FROM CENTRE OF EXHAUST TO REAR OF CAN .
36 - 50 SIZE 240MM
ANYTHING ABOVE 60 WE RECOMMEND TWO PIECING THE PIPE DUE TO THE WEIGHT OF THE CAN. WE SELL THE AIRFRAME CLAMPS AND THE SILICONE JOINERS
60 - 90 SIZE 300MM
90 - 120 SIZE 320MM
WE ARE AT THE END OF THE PHONE FOR ANY PROBLEMS YOU MAY HAVE.